Pvc Target Stand

 This is what you will need for this project:


(2)  1/2 in. tees
(2)  1/2 in. 90 degree elbows
(4)  1/2 in. caps
1 piece of 1/2 in. pvc (at least 108 inches)



First you will need to cut your pipe to these lengths:


(4)  6 inch pieces
(2)  2 1/2 foot pieces
(1)  2 foot piece



Now you will take one tee and add a six inch piece on each end of the tee and a cap on the other end of the six inch pieces. Then put a 2 1/2 foot piece on the top of the tee. Now on the top of of the 2 1/2 foot piece, put a elbow and now repeat that process. Now you have two big pieces.Next you will connect them at the top with the 2 foot piece on the elbows. Now you have your self a nice homemade target stand. Red solo cups can be connected with thin rope.

<<<<<>>>>>

Stress Balls

 These are the supplies you will need for this project:



1 bag of flour
1 pack of party balloons
1 water bottle



 First you will empty your water bottle. Then you will dry out the water bottle and fill it with flour. Now you will blow up your balloon and twist the neck of the balloon and put it over the top of the water bottle. Then you will let the balloon untwist and turn the water bottle and balloon upside down and let the amount of flour you desire in the bottle. Take the neck of the balloon off the water bottle and slowly let the air out. Once all the air is out tie the balloon and you're done.

<<<<<>>>>>

Marshmallow Mini Gun

Supplies you will need for this project:

1 piece of 1/2 inch pvc pipe (at least 35 inches)
2 (1/2) inch tees
2 (1/2) inch end caps
1 (1/2) inch 45 degree elbow
1 (1/2) inch slip adapter
1 (1/2) inch coupler

Directions:
First you will take your pvc and cut:

(3) 5-inch pieces
(1) 18-inch piece
(2) 1-inch pieces


Now you will take a 5-inch piece and add a coupler on one end and a tee on the other end. Then on the other end of the tee attach the 18-inch piece. After that put a five inch piece on the bottom of the tee and put a cap on the end of  that five inch piece. Now on the other end of the 18-inch piece put a tee and on the bottom of it put a 5-inch piece of pipe with a cap on the end. Then you put a 1-inch piece on the other end of the tee. Now on the end of that put a 45 degree elbow upright and a 1-inch piece on the end of that. Then attach your slip adapter. So now you have a fun marshmallow gun for friends and family.

Simple Blowgun

To make this blowgun you will need:
1 section of 1/2" pvc pipe (at least 2 1/2 feet long)
1 (1/2") slip adapter
1 roll decorative duct tape (optional)
1 roll electrical tape

Directions:
First you take your piece of pvc and cut a 2 1/2 foot piece. Then add your slip adapter for mouthpiece. Now you have a super simple blowgun. But lets take it to the next level and add a custom wrap. I picked up a roll of camo duct tape and wrapped mine long ways. Then I wrapped both ends with electrical tape. You will get to see how to make attachments in another project.

With a blowgun you have to have ammo here's the supplies:
1 cone party hat
1 pack of sticky notes
1 pack of #17 wire nails (optional)
 Hot glue gun and glue sticks or poster putty
1 roll of clear tape

Directions for ammo:
Take sticky note and wrap it around tip of party hat and make cone with sticky note. Hold it together with tape. Then take cone and roll it around in the end of pvc pipe till there is a notch. Cut on the line, now you have a little paper dart so now you can stick the nail in the end of the dart and pull it till it catches.Then put hot glue in and let it dry upright. Or if you want non-lethal ammo you can not put in the nails and they fly straight and accurate. If you want even softer ammo use small marshmallows they are fun for friends and family.

<<<<<>>>>>